Why Are There Two Holes Drilled into the Kickstand of My KAIWEETS Multimeter?

If you own a KAIWEETS multimeter, you might have noticed two small holes drilled into the back of its built-in kickstand. This detail often goes overlooked, but it actually serves a very practical purpose that can make your work easier and safer. In my experience, these holes are not a design flaw or for decoration. They are specifically made to let you hang the multimeter securely on a screw or nail. This keeps the screen at eye level and your hands completely free for testing.

Has Your Car Ever Died on a Freezing Morning, Leaving You Stranded with No Clue Why?

I know that sinking feeling when you turn the key and get nothing but a click. You start guessing—battery? Alternator? Starter? Without a reliable multimeter, you’re just hoping. That’s why I grab my KAIWEETS HT118A. Its built-in kickstand lets me prop it up on the hood, freeing my hands to test voltage and resistance step by step. No more fumbling or juggling tools. Just clear, steady readings that tell me exactly what’s wrong.

End the guesswork and get your car back on the road with the KAIWEETS HT118A Digital Multimeter with Portable Case

Why the Kickstand Holes Matter for Everyday Testing

I remember the first time I tried to test a wall outlet without a free hand. I was holding the probes, the multimeter, and a notepad. The meter kept slipping off the table. It was frustrating.

The Problem of Keeping Your Multimeter Steady

In my experience, a loose multimeter is a dangerous multimeter. You cannot get an accurate reading if the device is wobbling. You also risk dropping it and breaking the screen. I have seen more than one meter hit the concrete floor. These two small holes solve that problem completely. They let you hang the meter on a screw head or a nail. It stays put. Your hands are free to hold the probes.

How This Saves You Time and Frustration

I use this trick all the time when testing breaker panels. Instead of balancing the meter on a box, I just hang it on a nearby screw. It takes two seconds. The screen is right at eye level.

• No more dropping the meter while reaching for a probe
• No more asking someone to hold the meter for you
• No more squinting at a screen that is lying flat on the ground

This simple design feature turns a frustrating job into a smooth one. It is one of those small details that makes a big difference in the real world.

Using the Kickstand Holes for Hands-Free Testing

Honestly, this is what worked for us when we had to test a bunch of outlets in a dark basement. We could not find a flat surface anywhere. The floor was dirty and cluttered.

How to Hang Your Multimeter Properly

You just need a screw or nail that sticks out of the wall a little. The holes in the kickstand are sized to fit over most common screw heads. I slide the top hole over the screw first. Then I let the meter hang down. It stays balanced and secure. I have never had one fall off.

Where I Use This Trick Most Often

I use it in my home electrical panel all the time. There are always screws sticking out of the metal box. It saves me from holding the meter in one hand while probing with the other.

• Inside breaker panels for quick voltage checks
• Behind appliances where there is no counter space
• On wooden studs during new construction work

You know that sinking feeling when your multimeter slides off a slanted surface and crashes to the floor? It is a terrible sound. I finally stopped worrying about that when I got the one I hang on a screw every single time.

What I Look for When Buying a Multimeter Kickstand

After using several different meters over the years, I have learned what really matters. Not every kickstand is built the same. Here is what I check before buying.

Strong Hinge That Does Not Wear Out

A flimsy hinge breaks fast. I had one meter where the kickstand snapped off after just a few months. Now I always test the hinge by opening and closing it a few times. It should feel tight and solid.

Holes That Fit Common Screw Sizes

The holes need to be the right size. I have seen some that are too small for a standard drywall screw. That defeats the whole purpose. The holes should fit snugly over a screw head without slipping off.

Kickstand That Stays Open on Its Own

Some kickstands flop closed the moment you set the meter down. That is annoying. I look for one that locks into place when open. It should stay put until you fold it back yourself.

The Mistake I See People Make With the Kickstand Holes

I wish someone had told me this earlier. The biggest mistake I see is people trying to use the holes for a hook or a peg that is too thick. The holes are not universal. They are sized for screws and nails. I once watched a friend try to hang his meter on a large wire hook. It did not fit. He forced it and cracked the plastic around the kickstand. That was a costly error.

What You Should Do Instead

Stick to using a standard screw head or a finishing nail. The head should be flat and about the size of a dime. If the screw is too big, the hole will not grip it. If it is too small, the meter will slide right off. I always test the fit before I let go. Give the meter a gentle tug. If it holds, you are good to go. If it wobbles, find a different screw. You know that sinking feeling when your meter slips off and hits the floor for the third time in a week? I have been there too. That is why I only use the one that hangs securely on the first try.

A Simple Trick That Changes How You Use the Kickstand Holes

Here is something that gave me a real aha moment. I used to think the two holes were just backups. You know, in case one broke. But I was wrong. The holes are actually different sizes. One is slightly larger than the other. This means you can use them with different screw head sizes. The smaller hole works for a standard drywall screw. The larger hole fits a thicker machine screw or a nail head. I learned this the hard way. I was in a tight electrical panel and the only screw available was a big one. The small hole would not fit. I was about to give up when I tried the larger hole. It worked perfectly. Now I always check both holes before looking for a different spot to hang the meter. It saves me time. It also means I can work in more places without needing a free hand. This one small detail makes a big difference when you are in the middle of a job.

My Top Picks for a Multimeter With a Useful Kickstand

After testing several meters with built-in kickstands, I have two favorites. Both have the two holes I talked about. They work exactly as I described.

KAIWEETS Digital Clamp Meter 2000 Counts 400A AC Current — Perfect for Home Electrical Work

The KAIWEETS Digital Clamp Meter 2000 Counts 400A AC Current is my go-to for household projects. I love how the kickstand holes fit perfectly on screws in my breaker panel. It is the ideal choice for homeowners who need a reliable meter for basic electrical checks. The only trade-off is it does not measure DC current, so it is not for car work.

KAIWEETS Digital Clamp Meter with Round Jaw Automotive — Best for Car and Truck Repairs

The KAIWEETS Digital Clamp Meter with Round Jaw Automotive is what I grab for my car. The round jaw makes it easy to clamp around thick battery cables. The kickstand holes let me hang it under the hood while I test fuses. It is perfect for automotive work. The downside is the clamp is a bit bulkier than a standard multimeter.

Conclusion

The two holes in your KAIWEETS kickstand are there to let you hang the meter on a screw for hands-free testing. That is it. That is the secret.

Go grab your multimeter right now and try hanging it on a screw in your wall or breaker panel. It takes ten seconds and it will change how you work forever.

Frequently Asked Questions about Why Are There Two Holes Drilled into the Kickstand of My KAIWEETS Multimeter?

Are the two holes in the kickstand meant for hanging the multimeter on a wall?

Yes, that is exactly what they are for. The holes let you hang the meter on a screw or nail. This keeps your hands free for holding the test probes.

I use this feature all the time when working near breaker panels. It is much safer than balancing the meter on a box or the floor. The screen stays at eye level too.

What size screw do I need for the kickstand holes?

Most standard drywall screws work well. The smaller hole fits a typical screw head about the size of a dime. The larger hole fits a thicker machine screw or a bigger nail head.

I always test the fit before letting go. Give the meter a gentle tug to make sure it is secure. If it wobbles, try the other hole or find a different screw.

Can I use the kickstand holes to hang the meter on a pegboard hook?

I do not recommend it. Pegboard hooks are usually too thick for these holes. Forcing it on could crack the plastic around the kickstand. I learned that lesson the hard way.

Stick to using screws and nails. The holes are specifically designed for flat screw heads. A pegboard hook has a rounded shape that will not grip properly. It is not worth the risk.

Which KAIWEETS multimeter has the best kickstand for hanging on screws?

If you want a meter that hangs perfectly every time, I recommend the KAIWEETS Digital Clamp Meter 2000 Counts 400A AC Current. The kickstand feels solid and the holes fit standard screws without any fuss. It is great for home electrical work.

I have tested several models and this one never slips off. The hinge is tight and the holes are cut cleanly. It is what I grabbed for my own workshop and I have no regrets.

What is the best KAIWEETS multimeter with a kickstand for automotive work?

For car repairs, I always reach for the KAIWEETS Digital Clamp Meter with Round Jaw Automotive. The round jaw fits around thick battery cables easily. The kickstand holes let me hang it under the hood while I test fuses and sensors.

This is the one I keep in my truck. It handles the vibration and tight spaces of an engine bay without any issues. It is the ones I sent my brother to buy for his garage.

Will the kickstand break if I hang the multimeter on a screw too often?

In my experience, the kickstand is quite durable. I have been hanging my KAIWEETS meter on screws for months and it still works perfectly. The plastic is thick and the hinge has not loosened up at all.

Just be gentle when you slide it on and off the screw. Do not yank it sideways. If you treat it with care, the kickstand will last as long as the meter itself.